A euro slot is the interface that makes retail hang-pack work: a rounded slot that lets a product hang on a 25 mm pitch peg, facing out, without taking shelf space. For apparel brands it shows colour at a glance and cuts folding labour — but get the slot geometry, card stock or load math wrong and the pack tears or drops on day one.

1. What a euro slot is and why retail chains specify it

The standard slot is 30 × 10 mm with a rounded end, its centre 12–15 mm from the card's top edge. Mini packs use 25 × 8 mm and heavier sets 35 × 15 mm. The slot does more than hang the product: it fixes the height on the peg, whether the face points at the shopper, and whether staff can restock one-handed.

2. Slot types, tolerances and how they are cut

Slot type Size (mm) Typical use Suggested stock
Standard euro slot 30 × 10 Hang card, single garment 350–400 g/m² card
Mini slot 25 × 8 Hosiery, small accessories 300–350 g/m²
Large slot 35 × 15 Multi-piece sets, denim 400 g/m² plus reinforcement
Round hole Diameter 6 Hang tag with cord Not for peg hooks

Keep tolerance within ±0.5 mm and leave at least 8 mm of card between slot and edge — thin margins cause most tears. Die cutting gives a clean edge that resists fraying; hot-knife cutting is faster but hardens the edge, which cracks at the stress point under load.

3. Load: how much a peg pack can actually carry

A 350–400 g/m² coated card with a standard slot carries roughly 0.8–1.5 kg safely. Below 300 g/m² the card softens in humid stores and real capacity drops by about 30%. OPP film at 40–60 μm carries nothing itself — the card and any reinforcement patch take the whole load.

  • Above 1.5 kg switch to a double slot, a metal eyelet or a hook box
  • Peg pitch is 25 mm; leave a 5–8 mm gap between neighbouring SKUs
  • Gloss lamination weakens the slot edge; use matte or no lamination on heavy packs
  • Run a 24-hour fully loaded hang test before shipping

4. Header card design: size, slot position and barcode

Header cards run 60–120 mm tall and match the bag width, typically 100–150 mm. Keep the barcode at least 12 mm from the slot and 5 mm from any edge; otherwise scan failures become routine. Peg heights in store are finite, so an oversized header pushes the product out of the sight line.

5. Film choice: euro-hole bag, punched bag, reinforcement patch

OPP at 40–60 μm is clear and suits categories where colour must be visible; PE is tougher but hazier and makes dark garments look grey. A clear bag plus a paper reinforcement patch is the common combination. If the brand needs recyclability, specify a mono-material film (mono-PE or mono-PP) and design the card to detach, so stores can sort the two streams.

6. Packaging law and recycling marks

The EU PPWR (EU) 2025/40 requires recyclable design, recycled content and packaging minimisation, and a hang pack is sales packaging. Germany adds VerpackG registration and LUCID, France requires the Triman and Info-tri sorting marks, and Spain taxes non-reusable plastic packaging under Ley 7/2022. Japan's Containers and Packaging Recycling Law requires the plastic mark, and Korea's recycling act requires separation marks. Marks must match the material actually used: card and film are two streams and are marked separately.

7. Pre-shipment checklist

  • Slot centre 12–15 mm from the top edge, tolerance ±0.5 mm
  • Card at 350 g/m² or above with at least 8 mm margin
  • No crack or deformation after a 24-hour fully loaded hang test
  • Barcode at least 12 mm from the slot and scanning first time in store
  • Recycling marks match the actual card and film materials
The cost difference in hang packing is not the card or the film — it is the tear in the store. One dropped pack is one complaint plus one lost facing. A few percent more on card weight and reinforcement is cheaper than restocking.

Related Articles

Send the peg spec, bag width and unit weight; we will return a complete slot, card and film specification.

Request a euro-hole pack sample