Silicone gripper tape is the faintly tacky strip inside a waistband or a shoulder strap: a silicone dot pattern or stripe printed onto elastic tape or woven tape so that friction holds the garment in place. It is a cheap trim that decides return rates and fit complaints, because it does not fail at the factory. It fails after the fifteenth wash.
1. Three constructions to separate before quoting
- Silicone dots on elastic tape: the commonest form, usually polyester and elastane, where dot size and pitch set both hand feel and wear resistance; suited to waistbands and necklines.
- Silicone stripe on woven tape: a continuous line with higher adhesion demands, mostly used on the inner waist of trousers and on jacket hems.
- Clear silicone tape on release paper: heat-bonded or sewn on, used on straps, necklines and body-contact points, and easy to add at a later production stage.
2. Seven numbers to settle before sampling
The ranges below are what we normally run; the sample is the authority. They have to be written into the spec sheet, because a gripper tape described only verbally comes back as a different tape.
| Parameter | Typical range | Why it matters |
|---|---|---|
| Base tape width | 10–40 mm | Sets seam allowance and load: a narrow tape concentrates stress and breaks first |
| Silicone coating weight | 40–120 g/m² | Too thin wears off, too thick feels tacky and traps heat |
| Dot size and pitch | 3–6 mm | Pitch too tight merges into a sheet and kills stretch |
| Silicone hardness | Shore A 30–60 | Soft is comfortable on skin but wears faster; hard lasts longer and feels rough |
| Peel adhesion | ≥3 N/25 mm | Below this, edges lift after washing |
| Wash cycles | 20–30 cycles at 40 °C | Test to an ISO 6330 method, not hand washing alone |
| Stretch and recovery | 120–180% of original | Must match the base tape, or the tape corrugates on its own |
3. Silicone or PVC: why we no longer recommend PVC
PVC is softened with phthalate plasticisers, and those substances are restricted in consumer articles under Annex XVII of REACH, Regulation (EC) No 1907/2006; US CPSIA also limits eight phthalates in children's products to 0.1% combined. Silicone contains no plasticiser and holds up better to heat and washing, at a usual cost premium of 20–40%. European spec sheets now say no PVC outright, and switching early is cheaper than a failed inspection.
4. Most failures happen at heat bonding and at washing
Heat bonding parameters have to be given as a set: temperature, pressure and time, for example 150 °C, 2 bar, 15 seconds, then 24 hours of rest before peel testing. Adhesion measured straight off the press reads high and drops overnight. Wash to an ISO 6330 40 °C programme at both 5 and 20 cycles, and keep tumble drying under 60 °C. One overlooked cause: fabric softener leaves a film on the silicone that lowers friction, so the customer reports slipping when the tape is intact.
5. The care label still has to declare the base fibre
The gripper tape is not a label, but it is a textile: EU Regulation (EU) 1007/2011 requires fibre composition, so a polyester and elastane tape has to state both percentages, and US 16 CFR 303 requires composition plus care instructions. Japan asks for fibre content and care symbols under the Household Goods Quality Labeling Act; Korea requires quality marking with fibre content, care warnings, manufacturer and origin. The commonest mistake is filing the tape as an accessory and declaring no fibre content, which an inspection will read as a textile.
6. Five checks before ordering
- Structure (dots, stripe or lined tape) and base fibre are written down
- Width, coating weight, dot pitch, hardness and peel strength are all specified
- Both 5-cycle and 20-cycle washes are tested, with 24 hours of rest after bonding
- The care label declares the base fibre and the maximum drying temperature
- Check whether the destination market restricts PVC, and keep a silicone reference sample
Related Articles
- Elastic trims: width, stretch and recovery
- Jacquard elastic waistbands: structure and hand feel
- Drawcords and cord ends: spec and testing
Need samples, size confirmation or gripper tape testing?
Request samples and a quote →