A printed fabric label is printed on ready-made tape — satin, taffeta, grosgrain or cotton — instead of being woven on a jacquard loom. That one decision changes the cost structure, the minimum order, how fine the type can be, and what is left of the label after twenty washes. This guide compares the four tapes TAGE prints most often, sets out where rotary screen printing beats thermal transfer and the other way round, and lists the artwork and edge-finishing rules that decide whether a 15 mm label stays legible. Every rule below can be copied straight into a purchase order.
1. Printed or Woven: The Decision That Sets Everything Else
A woven label builds the image from coloured yarn, so the logo cannot rub off, but the finest type is limited by warp density — roughly 25–40 ends per centimetre on garment labels. A printed label puts ink on the surface of a smooth tape, so 1 mm type and thin serifs are possible, six colours go down in one pass, and the tape can carry variable data such as size, lot or serial number. The trade-off is surface ink: it sits on the fibre and has to survive washing, so ink choice and a wash test matter more than they do on a woven label. In practice most brands print the care and size labels and choose between woven and printed for the brand mark depending on how fine the artwork is.
2. Four Substrates and What Each Can Print
The tape decides the printing method, the minimum width and the hand feel against the neck. The ranges below are what TAGE keeps in stock; outside them the tape has to be made to order, which adds two to three weeks.
| Tape | Surface and print result | Typical width | Best for | Watch out |
|---|---|---|---|---|
| Polyester satin | Glossy and smooth; sharpest fine type and small logos; ink sits on top | 15–40 mm | Brand label at neck or side seam | Lowest rub fastness of the four; test after washing |
| Polyester taffeta | Matte and firm; crisp small type; cheapest of the synthetics | 15–50 mm | Care and size labels | Needle marks show; use a finer needle |
| Grosgrain | Ribbed surface; bold artwork only, fine serifs fill in | 10–38 mm | Workwear, denim, unisex | Type under 1.5 mm fills the ribs |
| Cotton tape | Natural hand feel and matte; ink absorbs and edges soften | 10–30 mm | Organic and natural-positioning ranges | Shrinks 2–4% on the first wash; allow for it in the fold |
3. Printing Methods: Where Each One Wins
Quantity, colour count and whether the data changes per piece decide the method. Mixing two methods within one order is normal; there is no need to commit the whole collection to one.
- Rotary screen: one screen per colour, so it wins from a few thousand pieces upward and lands Pantone spot colours accurately; six colours are practical on a 20 mm tape.
- Thermal transfer: no screen and no plate, the file goes straight to the line, which makes it the default for short runs and for labels where size or lot number changes piece by piece.
- Digital toner or inkjet: best for proofs, sample sets and one-off artwork tests; unit cost stays high, so it rarely becomes the production route above a few hundred pieces.
4. Artwork Rules That Survive the Tape
Tape printing fails for boring reasons: type too small, lines too thin, reversed type. These thresholds are what TAGE checks before a proof is issued; running through them yourself saves one round of emails.
- Cap height of at least 1.2 mm for Latin text and 1.5 mm for Chinese, Japanese or Korean characters; below that the ink spreads into the counters.
- No line thinner than 0.25 mm, and no reversed type (white on colour) below 6 pt — the ink bleeds and fills the letters.
- Barcodes belong on taffeta, not satin: the gloss reflects the scanner beam and the read rate drops. Keep a 3 mm quiet zone on each side.
5. Edges, Folds and Stitch Allowance
A printed tape has two cut ends, and a cut end frays in the wash unless it is sealed. Hot cutting or ultrasonic cutting welds the yarn ends and is the standard for satin and taffeta; cotton tape is usually folded and stitched instead, because a welded edge stiffens the end. Folds follow the sewing position: an end fold turns both short ends under and needs 10 mm of extra cut length; a centre fold doubles the tape for a neck label and needs no extra length but must state the fold line; a miter fold turns all four edges for a label stitched on all sides. Put the cut length, the fold type and the stitch allowance on the purchase order — a 20 mm tape with an end fold consumes about 30 mm of material per label, and that is what you are paying for.
6. Wash Durability and What Each Market Requires
Durability is a test, not a claim. Ask for ISO 105-C06 wash fastness at 40 °C and ISO 105-X12 rub fastness results on the actual tape and the actual ink, then wash three production labels once and read them again: if 1.2 mm text closes up, it was already too small. Content is where markets diverge most. In the EU, Regulation (EU) No 1007/2011 requires the fibre composition on a permanent label and EN ISO 3758 governs the care symbols. France adds the responsible party's identity and the French wording for care terms under the consumer code; Spain requires the same information in Spanish. In Japan the Household Goods Quality Labelling Act requires fibre composition, care symbols under JIS L 0001, the labeller's name and address, and the country of origin. In Korea, fibre content, care symbols under KS K 0021 and the country of origin are mandatory. One artwork cannot serve four markets at once — which is exactly why printed labels own the care text: you change the file, not the weaving programme.
Related Articles
Send the artwork and the tape you have in mind; we print 15 mm and 25 mm proofs on two substrates and return a 10× scan with the measured type height.
Request printed label proofs and a quote →